|
|
PDF SPO18 Data sheet ( Hoja de datos )
| Número de pieza | SPO18 | |
| Descripción | (SPO15 / SPO18) Installation Instructions | |
| Fabricantes | Rotary | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SPO18 (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
|
No Preview Available !
SPO15, SPO18
Sprinter SPO15 (3A0 Lifts) Capacity 11,000 lbs.
Standard SPO15 (300 Series Lifts) Capacity 15,000 lbs.
Standard SPO18 (300 Series Lifts) Capacity 18,000 lbs.
II
NN
SS
TT
AA
LL
LL
AA
TT
II
OO
NN
LP20293
© September 2007 by Rotary Lift. All rights reserved. CO6953.6
IN20379
Rev. C 09/12/2007
II
NN
SS
TT
RR
UU
CC
TT
II
OO
NN
SS
Free Datasheet http://www.datasheet4u.net/
1 page  
Hose Routes Diagonally Across Overhead
Fig. 7b
Use (4) 5/16”-18NC x 1-1/2” HHCS And Nuts
On one bolt place
(2) 5/16” Star Washers
Push nuts hold bolts to brackets
CAPACITY
15,000 LBS.
For SPO15
CAPACITY
18,000 LBS.
For SPO18
Fill Breather Cap
Fig. 8a
Overhead Hose
Fig. 8b
Branch Tee
Crimped Hose
Sleeve (Typical)
Power Unit (Short) Hose
10. Equalizer Cables: Fig. 10 describes general cable
arrangements. It is easier to tie-off lower studs first.
A) Run cable stud up through the lower tie-off plate,
and/or bracket(s), and/or spacer(s) depending on the
lift model, Fig. 11.
B) Push cable up until stud is above top of carriage Fig.
11.
C) Run nylon insert locknut onto studs so that 1/2" ex-
tends out from locknut Fig. 11.
D) Pull cables back down through carriage Fig. 11.
E) Run cable overhead and tie-off top studs and torque to
about 100 in-lbs., see Fig. 10 & Fig. 11.
5
Hose runs through holes in
7 extensions, then through
holes in overhead.
3
Hose runs down
approach side to
cylinder on left column.
5
4 Cylinder bleeders
Torque values
15 ft. lbs. Minimum
20 ft. lbs. Maximum
7
5
1
2
6 FRONT
5
Fig. 9
ITEM
1
2
3
4
5
5
6
6
7
7
7
QTY.
2
1
1
1
3
3
1
1
2
2
2
DESCRIPTION
Hydraulic Cylinder
Power Unit Hose
Overhead Hose
Branch Tee
Hose Clips(5/8")
5/16"-18NC x 3/8” lg. PHMS
Hose Clips(1/2")
5/16"-18NC x 3/8” lg. PHMS
Hose Clips(5/8")
5/16"-18NC x 1/2” lg. PHMS
5/16"-18NC Nut
Upper Sheaves
2nd Cable
1st Cable
Lower Sheaves
Fig. 10
Free Datasheet http://www.datasheet4u.net/
5 Page 
17. Door Bumper Installation:
1) Press bumpers on column edge and carriage, Fig. 22.
Note: Door Bumpers may need to be installed in
different areas depending upon type(s) of vehicles used.
The above installation is the most recommended.
21. Adapter Rack: Install adapter rack, Fig. 24. Place
extension in racks.
Column
(4) 5" Extensions
Adapter Rack
Door Bumpers
(2) 5/16" x 3/8" Lg.
pan head screws
Fig. 22
21"
(2) 10" Extensions
Fig. 24
18. Pressure Test: Run lift to full rise and keep motor
running for 5 seconds. Stop and check all hose connec-
tions. Tighten or reseal if required. Repeat air bleeding of
cylinders.
19. Final Adjustments: Raise lift to check equalizer
cable tension. Below carriage, grasp adjacent cables
between thumb and forefinger, with about 15 lbs. effort
you should just pull the cables together. Adjust at upper
tie-offs, Fig. 11.
20. Decal Location: Install enclosed pinch point decals.
Place (1) decal on each column, Fig. 23.
WARNING (2)qty. 10" adapter extensions and (4)qty.
5" adapter extensions are supplied with each lift. These
extensions should not be stacked more than 15" high.
WARNING
Keep feet
clear of lift
while lowering
Fig. 23
WARNING
Place WARNING decal
a minimum of 8" from
the bottom of the decal
to the ground.
Keep feet
clear of lift
while lowering
11
Free Datasheet http://www.datasheet4u.net/
11 Page | ||
| Páginas | Total 12 Páginas | |
| PDF Descargar | [ Datasheet SPO18.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SPO15 | (SPO15 / SPO18) Operation & Maintenance Manual | Rotary |
| SPO15 | (SPO15 / SPO18) Parts Breakdown | Rotary |
| SPO15 | (SPO15 / SPO18) Installation Instructions | Rotary |
| SPO18 | (SPO15 / SPO18) Operation & Maintenance Manual | Rotary |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |