|
|
PDF SP385E Data sheet ( Hoja de datos )
| Número de pieza | SP385E | |
| Descripción | Enhanced +3V or +5V RS-232 Line Driver/Receiver | |
| Fabricantes | Sipex | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SP385E (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
®
SP385E
Enhanced +3V or +5V RS-232 Line
Driver/Receiver
s Operates from 3.3V or 5V Power Supply
s Meets All EIA-232D and V.28 Specifica-
tions at 5V
s Meets EIA-562 Specifications at 3.3V
s Two Drivers and Receivers
s Operates with 0.1µF to 10µF Capacitors
s High Data Rate — 120kbps Under Load
s Low Power Shutdown ≤1µA
s 3-State TTL/CMOS Receiver Outputs
s Low Power CMOS — 5mA Operation
s Improved ESD Specifications:
+15kV Human Body Model
+15kV IEC1000-4-2 Air Discharge
+8kV IEC1000-4-2 Contact Discharge
DESCRIPTION…
The Sipex SP385E is an enhanced version of the Sipex SP200 family of RS232 line drivers/
receivers. The SP385E offers +3.3V operation for EIA-562 and EIA-232 applications. The
SP385E maintains the same performance features offered in its predecessors. The SP385E is
available in plastic SOIC or SSOP packages operating over the commercial and industrial
temperature ranges. The SP385E is pin compatible to the LTC1385 EIA-562 transceiver, except
the drivers in the SP385E can only be disabled with the ON/OFF pin.
RS232 OUTPUTS RS232 INPUTS
CHARGE
PUMP
T1 T2
R1 R2
Rev. 10/22/01
TTL/CMOS INPUTS TTL/CMOS OUTPUTS
SP385E Enhanced +3V to +5V RS-232 Line Driver/Receiver
1
© Copyright 2001 Sipex Corporation
1 page  
FEATURES…
The Sipex SP385E is a +3V to +5V EIA-232/EIA-
562 line transceiver. It is a pin-for-pin alternative for
the SP310A and will operate in the same socket with
capacitors ranging from 0.1µF to 10µF, either polar-
izedornon–polarized,in+3Vsupplies. TheSP385E
offers the same features such as 120kbps guaranteed
transmission rate, increased drive current for longer
and more flexible cable configurations, low power
dissipation and overall ruggedized construction for
commercialandindustrialenvironments. TheSP385E
also includes a shutdown feature that tri-states the
drivers and the receivers.
The SP385E includes a charge pump voltage con-
verter which allows it to operate from a single +3.3V
or +5V supply. These converters double the VCC
voltage input in order to generate the EIA-232 or EIA-
562 output levels. For +5V operation, the SP385E
driver outputs adhere to all EIA-232D and CCITT
V.28 specifications. While at +3.3V operation, the
outputs adhere to EIA-562 specifications. Due to
Sipex's efficient charge pump design, the charge
pump levels and the driver outputs are less noisy than
other 3V EIA-232 transceivers.
The SP385E has a single control line which simul-
taneously shuts down the internal DC/DC con-
verter and puts all transmitter and receiver outputs
into a high impedance state.
The SP385E is available in 18-pin plastic SOIC
and 20-pin plastic SSOP packages for operation
over commercial and industrial temperature
ranges. Please consult the factory for surface-
mount packaged parts supplied on tape-on-reel
as well as parts screened to MIL-M-38510.
The SP385E is ideal for +3.3V battery applica-
tions requiring low power operation. The charge
pump strength allows the drivers to provide
±4.0V signals, plenty for typical EIA-232 appli-
cations since the EIA-232 receivers have input
sensitivity levels of less than ±3V.
THEORY OF OPERATION
The SP385E device is made up of three basic
circuit blocks — 1) a driver/transmitter, 2) a re-
ceiver and 3) a charge pump.
Driver/Transmitter
The drivers are inverting transmitters, which ac-
cept TTL or CMOS inputs and output the RS-232
signals with an inverted sense relative to the input
logic levels. Typically the RS-232 output voltage
swing is ±9V for 5V supply and ±4.2V for 3.3V
supply. Even under worst case loading conditions
of 3kΩ and 2500pF, the output is guaranteed to be
±5V for a 5V supply and ±3.7V for a 3.3V supply
which adheres to EIA-232 and EIA-562 specifica-
tions, respectively. The transmitter outputs are
protected against infinite short-circuits to ground
without degradation in reliability.
The instantaneous slew rate of the transmitter
output is internally limited to a maximum of 30V/
µs in order to meet the standards [EIA 232-D 2.1.7,
Paragraph (5)]. However, the transition region
slew rate of these enhanced products is typically
10V/µs. The smooth transition of the loaded out-
put from VOL to VOH clearly meets the monotonic-
ity requirements of the standard [EIA 232-D 2.1.7,
Paragraphs (1) & (2)].
Receivers
The receivers convert RS-232 input signals to
inverted TTL signals. Since the input is usually
from a transmission line, where long cable lengths
and system interference can degrade the signal, the
inputs have a typical hysteresis margin of 500mV.
This ensures that the receiver is virtually immune
to noisy transmission lines.
The input thresholds are 0.8V minimum and 2.4V
maximum, again well within the ±3V RS-232
requirements. The receiver inputs are also pro-
tected against voltages up to ±15V. Should an
input be left unconnected, a 5kΩ pull-down resis-
tor to ground will commit the output of the receiver
to a high state.
In actual system applications, it is quite possible
for signals to be applied to the receiver inputs
before power is applied to the receiver circuitry.
This occurs for example when a PC user attempts
to print only to realize the printer wasn’t turned on.
In this case an RS-232 signal from the PC will
appear on the receiver input at the printer. When
the printer power is turned on, the receiver will
operate normally. All of these enhanced devices
are fully protected.
Rev. 10/22/01
SP385E Enhanced +3V to +5V RS-232 Line Driver/Receiver
5
© Copyright 2001 Sipex Corporation
5 Page 
ORDERING INFORMATION
Model ....................................................................................... Temperature Range ................................................................................ Package
SP385ECA ..................................................................................... 0°C to +70°C ............................................................................... 20–pin SSOP
SP385EEA ................................................................................... –40°C to +85°C ............................................................................. 20–pin SSOP
SP385ECT ..................................................................................... 0°C to +70°C ................................................................................ 18–pin SOIC
SP385EET ................................................................................... –40°C to +85°C .............................................................................. 18–pin SOIC
CT and ET packages available Tape–on–Reel. Please consult the factory for pricing and availability for this option, and for parts screened to
MIL–STD–883.
Corporation
SIGNAL PROCESSING EXCELLENCE
Sipex Corporation
Headquarters and
Sales Office
22 Linnell Circle
Billerica, MA 01821
TEL: (978) 667-8700
FAX: (978) 670-9001
e-mail: [email protected]
Sales Office
233 South Hillview Drive
Milpitas, CA 95035
TEL: (408) 934-7500
FAX: (408) 935-7600
Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the
application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others.
Rev. 10/22/01
SP385E Enhanced +3V to +5V RS-232 Line Driver/Receiver
11
© Copyright 2001 Sipex Corporation
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet SP385E.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SP385A | +3V to +5V RS-232 Line Driver/Receiver | Sipex |
| SP385ACA | +3V to +5V RS-232 Line Driver/Receiver | Sipex |
| SP385ACT | +3V to +5V RS-232 Line Driver/Receiver | Sipex |
| SP385AEA | +3V to +5V RS-232 Line Driver/Receiver | Sipex |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |