|
|
PDF HS10 Data sheet ( Hoja de datos )
| Número de pieza | HS10 | |
| Descripción | Feed Sensor | |
| Fabricantes | Hog Slat | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de HS10 (archivo pdf) en la parte inferior de esta página. Total 3 Páginas | ||
|
No Preview Available !
Grow-FlexTM Feed System
HS10 Feed Sensor
Specifications:
Operating Voltage: 90-250 VAC
Frequency: 50-60 Hz
Relay Contact Maximum Current Load: 5A Resistive and 2A Inductive (Motors and Relays)
Sensitivity: 0-9/16” (Factory Setting is for ¼”)
Time Delay Range: 0-4 Hours (Factory Setting is for 30 seconds)
Ambient Operating Temperature: -4°F-+158°F
Cord: Length= 5’ 18-5 SJTW
These instructions are guidelines for new GrowerSelect installation in four (4) wire Sensor control units. In
all cases, the OEM (Original Equipment Manufacturer) wiring instructions should be followed if possible.
It is in no way to be used to violate or supersede local, state and national wiring codes. All wiring sizes and
fuse capacities are to be sized according to national electrical code specifications or other applicable
regulations.
For the purpose of installation:
• NC (Normally Closed) is defined as contacts closed (runs) with power supply connected to sensor
and no product in contact with sensor. (Black wires marked #1 & #3)
• NO (Normally Open) is defined as contacts open (does not run) with power supply connected to
sensor and no product in contact with sensor. (Black wires marked #1 & #4)
• COM (Common) is defined as common or supply for sensor circuit used in conjunction with NO or
NC leads. (Black Lead #1)
• L1 (Line 1) is defined as Line 1 of power supply circuit. (Brown wire)
• L2 (Line 2) is defined as Line 2 of power supply circuit. (Blue wire)
Mounting:
Sensor should be installed consistent with existing sensor mounting in rubber grommet or other suitable
mount. Replacement grommets can be purchased at your local Hog Slat retailer. Sensor should be
inserted into grommet so that 1/2” minimum of sensor protrudes past grommet into grain/feed area (Figure
1). It should be secured with supplied Nylon cable tie. Do not use hose clamp!
For new installations, use HS10-2 mounting kit and position sensor as shown in Figure 1.
Figure 1
Hog Slat Inc. Newton Grove, NC USA February 2015
1
1 page | ||
| Páginas | Total 3 Páginas | |
| PDF Descargar | [ Datasheet HS10.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| HS1-0508RH-Q | Radiation Hardened Single 8/Differential 4-Channel CMOS Analog Multiplexers |  Intersil Corporation |
| HS1-0509RH-Q | Radiation Hardened Single 8/Differential 4-Channel CMOS Analog Multiplexers | Intersil Corporation |
| HS1-0546RH-Q | Radiation Hardened Single 16/Differential 8 Channel CMOS Analog Multiplexers with Active Overvoltage Protection | Intersil Corporation |
| HS1-0547RH-Q | Radiation Hardened Single 16/Differential 8 Channel CMOS Analog Multiplexers with Active Overvoltage Protection | Intersil Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |