DataSheet.es    


PDF G104SN02_V1 Data sheet ( Hoja de datos )

Número de pieza G104SN02_V1
Descripción LCD Module
Fabricantes AUO 
Logotipo AUO Logotipo



Hay una vista previa y un enlace de descarga de G104SN02_V1 (archivo pdf) en la parte inferior de esta página.


Total 27 Páginas

No Preview Available ! G104SN02_V1 Hoja de datos, Descripción, Manual

www.DataSheet4U.net
Produktspezifikation für AUO G104SN02 V1
Im Programm von
Achtung:
Dieses Dokument unterliegt nicht dem Änderungsdienst. Der Stand
entspricht der Drucklegung. Bitte informieren Sie sich vor Verwendung
ob die technischen Daten noch dem aktuellen Stand entsprechen. Trotz
sorgfältiger Kontrolle können wir leider keine Haftung für Druckfehler
oder Irrtümer übernehmen.

1 page




G104SN02_V1 pdf
www.DataSheet4U.net
G104SN02 V1
1. Operating Precautions
1) Since front polarizer is easily damaged, please be cautious and not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or soft cloth.
5) Since the panel is made of glass, it may be broken or cracked if dropped or bumped on
hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human
earth when handling.
7) Do not open nor modify the module assembly.
8) Do not press the reflector sheet at the back of the module to any direction.
9) In case if a module has to be put back into the packing container slot after it was taken
out from the container, do not press the center of the CCFL Reflector edge. Instead,
press at the far ends of the CFL Reflector edge softly. Otherwise the TFT Module may
be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit
(IEC60950 or UL1950). Do not connect the CFL in Hazardous Voltage Circuit.
15) Severe temperature condition may result in different luminance, response time and lamp
ignition voltage.
16) Continuous operating TFT-LCD display under low temperature environment may accelerate
lamp exhaustion and reduce luminance dramatically.
17) The data on this specification sheet is applicable when LCD module is placed in landscape
position.
18) Continuous displaying fixed pattern may induce image sticking. It s recommended to use
screen saver or shuffle content periodically if fixed pattern is displayed on the screen.
G104SN02 V1 rev. 0.0
Page 4/26

5 Page





G104SN02_V1 arduino
www.DataSheet4U.net
4. Absolute Maximum Ratings
4.1 Absolute Ratings of TFT LCD Module
Item
Logic/LCD Drive
Symbol
Vin
Min
-0.3
Max
+4.0
4.2 Absolute Ratings of Environment
Item
Symbol
Min
Max
Operating Temperature
TOP
-30
+85
Operation Humidity
HOP
5
95
Storage Temperature
TST
-30
+85
Storage Humidity
HST
5
95
Note: Maximum Wet-Bulb should be 39and no condensation.
G104SN02 V1
Unit
[Volt]
Unit
[oC]
[%RH]
[oC]
[%RH]
G104SN02 V1 rev. 0.0
Page 10/26

11 Page







PáginasTotal 27 Páginas
PDF Descargar[ Datasheet G104SN02_V1.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
G104SN02-V0LCD ModuleAUO
AUO
G104SN02-V1LCD ModuleAUO
AUO
G104SN02-V2LCD ModuleAUO
AUO
G104SN02_V0LCD ModuleAUO
AUO

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar