|
|
Número de pieza | G084SN05-V2 | |
Descripción | Color TFT-LCD Module | |
Fabricantes | AUO | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de G084SN05-V2 (archivo pdf) en la parte inferior de esta página. Total 26 Páginas | ||
No Preview Available ! Spec. No.:
www.DataSheet4U.com
MDGD084-SN05-2
Version:
0.2
Total pages:
26
Date:
2004- March-15
AU OPTRONICS CORPORATION
Product Functional Specifications
8.4” SVGA Color TFT-LCD Module
Model Name: G084SN05 V.2
Approved by
Martin Sun
Prepared by
Cynthia Lin
GD- MDBU Marketing Division / AU Optronics Croporation
Customer
Checked & Approved by
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G084SN05 V.2 ver.0.2
1/1
1 page www.DataSheet4U.com
1.0 Handing Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnection from input
connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a module has to be put back into the packing container slot after once it was
taken out from the container, do not press the center of the CCFL Reflector edge.
Instead, press at the far ends of the CCFL Reflector edge softly. Otherwise the TFT
module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the interface Connector of the TFT module.
11) After installation of the TFT module into an enclosure, do not twist nor bend the TFT
module even momentary. At designing the enclosure, it should be taken into
consideration that no bending/twisting forces are applied to the TFT module from
outside. Otherwise the TFT module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please
follow local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module
should be supplied by power complied with requirements of Limited Power Source, or
be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current
Circuit. Do not connect the CCFL in Hazardous Voltage Circuit.
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G084SN05 V.2 ver.0.2
5/5
5 Page www.DataSheet4U.com
5.0 Signal Interface
5.1 Connectors
Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be
following components.
Connector Name
Description
Manufacturer
Connector 1
Digital Signal
Kyocera Elco
Connector 2
Lamp Control
JST
Connector 3
Analog Signal
HIROSE
Connctor 4/5
Lamp Power
JST
Type / Part
Number
04 6274 036 000 800 S5B-ZR-SM3A-TF DF13B-9P-1.25
Mating Connector
BHR-03VS-1
B-BHS-1-TB
5.2 Signal Pin
5.2.1 Digital Input Signal (Connector 1)
Pin No.
Signal Name
1 GND
3 DE_IN
5 VSYNC_IN
7 RIN0
9 RIN2
11 RIN4
13 GIN0
15 GIN2
17 GIN4
19 BIN0
21 BIN2
23 BIN4
25 GND
27 VDD
29 VDD
31 GND
33 GND
35 VBL
Pin No.
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
Signal Name
DCLK_IN
HSYNC_IN
GND
RIN1
RIN3
RIN5
GIN1
GIN3
GIN5
BIN1
BIN3
BIN5
REV
VDD
DIMMER
GND
VBL
VBL
(C) Copyright AU Optroncis, Inc.
2004 All Right Reserved.
No Reproduction and Redistribution Allowed.
G084SN05 V.2 ver.0.2
11/11
11 Page |
Páginas | Total 26 Páginas | |
PDF Descargar | [ Datasheet G084SN05-V2.PDF ] |
Número de pieza | Descripción | Fabricantes |
G084SN05-V0 | LCD Module | AUO |
G084SN05-V1 | LCD Module | AUO |
G084SN05-V2 | Color TFT-LCD Module | AUO |
G084SN05-V3 | Color TFT-LCD Module | AUO |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |